Product Details


PRODUCT SPECIFICATIONS

 TYPES OF PRODUCT

  • Mineral oil based oils for the engine that the manufacturer requires mineral based oils.
  • Synthetic based lubricants for the engine that the manufacturer requires Synthetic oils.

 DELIVERY, STORAGE AND HANDLING

  • Store products in manufacturer’s unopened packaging until ready for installation.
  • Store and dispose of materials in accordance with requirements of local authorities having jurisdiction.
  • Keep all Products in room temperature environment with low humidity.

EQUIPMENT ASSESSMENT  

  • Do not begin installation until the engine is operating at proper manufacturer specifications. All service lights and emissions should be recorded before installation.
  • Inspection of the oil dipstick showing the oil level will be necessary.
  • Ensure there is no chance of rain for the installation period if outdoors.
  • The engine must not be running to install. Installer must follow all engine manufacturer’s instructions for oil top off.

INSTALLATION

  • Only a qualified licensed automotive technician should do the installation.
  • Determine the proper amount of G4X to be installed into the units. This is equal 10% of the engine’s oil capacity.
  • Pour the G4X into the oil filler port as specified by the engine’s manufacturer.
  • Once the desired amount of G4X is installed, clean the area and ensure that any spills are contained and disposed of by the specifications of local governance.

WARRANTY

  • Manufacturer shall offer one (1) year limited warranty, commencing from the date of shipment providing lubricants manufactured to be free from defects in materials and workmanship under normal use and service. Oil samples will need to be provided to G4X manufacturer for analysis if failure of the engine is suspect.

 

TYPICAL PHYSICAL AND CHEMICAL PROPERTIES

 

SAE GRADE

SAE International (SAE) is a professional organization for mobility engineering professionals in the aerospace, automotive, and commercial vehicle industries. The Society is a standards development organization for the engineering of powered vehicles of all kinds, including cars, trucks, boats, aircraft, and others.

SPECIFIC GRAVITY, °

The ratio of the mass of a solid or liquid to the mass of an equal volume of distilled water at 4°C (39°F) or of a gas to an equal volume of air or hydrogen under prescribed conditions of temperature and pressure. Also called relative density.

VISCOSITY INDEX

Viscosity Index highlights how a lubricant’s viscosity changes with variations in temperature. Many lubricant applications require the lubricant to perform across a wide range of conditions: for example, in an engine. Automotive lubricants must reduce friction between engine components when it is started from cold (relative to engine operating temperatures) as well as when it is running (up to 200 °C). The best oils (with the highest VI) will not vary much in viscosity over such a temperature range and therefore will perform well throughout.

FLASH POINT

The flash point of a flammable liquid is the lowest temperature at which it can form an ignitable mixture in air. At this temperature the vapor may cease to burn when the source of ignition is removed. A slightly higher temperature, the fire point, is defined as the temperature at which the vapor continues to burn after being ignited. Neither of these parameters is related to the temperatures of the ignition source or of the burning liquid, which are much higher. The flash point is often used as one descriptive characteristic of liquid fuel, but it is also used to describe liquids that are not used intentionally as fuels.

POUR POINT

The pour point of a liquid is the lowest temperature at which it will pour or flow under prescribed conditions. It is a rough indication of the lowest temperature at which oil is readily pumpable. Also, the pour point can be defined as the minimum temperature of a liquid, particularly a lubricant, after which, on decreasing the temperature, the liquid ceases to flow.

 

TEST

METHOD

RESULTS

SAE GRADE

SAE J300

20w-30

GRAVITY SP @ 60⁰F

ASTM D-287

0.9986

VISCOSITY @ 40⁰C

ASTM D-445

54.63

VISCOSITY @ 100⁰C

ASTM D-445

9.57

VISCOSITY INDEX

ASTM D-2270

161

FLASH POINT, ⁰C

ASTM D-93

374

POUR POINT, ⁰C

ASTM D-97

-22